P65 Warning Label

Housing, Axles, and Center Section 3rd gen



SKU: TC101 Category:


Trick Chassis 9″ Rear axle for 3th gen Camaro and Firebird 1982 to 1992

Below is what comes with it for the base price:

  • Brand new center fabricated housing can (STANDARD) Others charge $100 more.
  • Internal axle tube gussets (STANDARD) Others charge $75 more.
  • 3″ .250 wall DOM axle tubes (STANDARD).
  • 4 lower control arm mounting holes (STANDARD).
  • 28, 31, 35 spline axle options (YOUR CHOICE).
  • Drive studs included 12mm, 1/2-2″,1/2-3″ (YOUR CHOICE).
  • Torque arm bracket is included.
  • Housing vent included.
  • wheel bearings included.
  • 10 nuts to bolt the center section in.
  • Yukon center section with a spool in it (your choice of gear).
  • Shipped bare steel.
  • We can narrow for free (see options).

Options for additional charge:

  • T bolt brake hardware kit (easy install of your stock F body backing plates).
  • Lube Locker Gasket (Super nice aluminum core gasket with orange elastomer beading).
  • 40 spline upgraded axles (gun drilled).
  • 5/8 wheel studs.
  • 11 Hole narrowed lower brackets.
  • Powder coat.
  • Fill and drain caps.
  • Stock sway bar brackets (these also allow you to bolt the under axle ARB on that I sell).
  • Coil over brackets.
  • Coil over brackets with no spring perches added.
  • Differential being used ( instead of spool).
  • non adjustable aftermarket torque arms do not fit without modification.
  • We recommend adjustable torque arms only

Please call or email us for pricing and estimated time:

  • We offer full bolt in assemblies.
  • Wishbone application.
  • Only torque arm and no other bracket setups.
  • Extreme custom applications (we have done many of these).
  • Crate and freight available.
  • International shipping* Our website will not calculate dutys/taxes/shipping/broker setups.

Important Shipping Information

Axles are shipped with no bearings on them. Your stock backing plate needs to go on first then the bearings get pressed on behind them.

Axles and center section are dropped shipped and may show up at an earlier or later time than the housing.

Important Brake Information

The Billet gm 10/12 (can use stock GM car brakes)  these only fit 3rd gen drums if you have a 4 hole backing plate. Otherwise this fits 2nd gen drum brake kits.

Additional information

Weight 130 lbs
Dimensions 60 × 19 × 15 in

Powder Coat

Gloss Black, Gloss Red, Semi Gloss Black

Model Year

1993 – 1997, 1998 – 2002

Axle Splines

28 Moser Axles, 28 Strange Engineering Axles, 31 Spline Moser Axles, 31 Strange Engineering Axles, 35 Spline Moser Axles, 35 Spline Strange Engineering Axles, 40 Spline Strange Engineering


4 channel ABS ring, None

Back Brace

None, Yes

Wheel Studs (Screw In)

1/2" Wide – 2" Long, 1/2" Wide – 3" Long, 12MM (Stock), 5/8" Wide – 3" Long

Fill & Drain Plug

Both Fill & Drain, Drain, Large Billet Fill, None

Housing Ends

Billet Big Bearing New Style, Billet Big Bearing Old Style, Billet Symmetrical Ends, Flush Mount GM (Can Use Stock F-Body Brakes)

Sway Bar Brackets

None, Yes

Rear End Length

1" Shorter (Each Side), 1/2" Shorter (Each Side), 2" Shorter (Each Side), 3" Shorter (Each Side), Stock Width


There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.